PAGE 1
HYP E R AQ80001G TOUGH 20V MAX HT CHARGE LITHIUM-ION CORDLESS CIRCULAR SAW INSTRUCTION MANUAL Maximum initial battery voltage (measured without load) is 20 Volts. Nominal voltage is 18. Electronic Version of this Manual Available on Walmart.
PAGE 2
Personal safety. Power tool use and care. Additional safety rule: Specific safety rules/Lower Guard, Specific safety Symbols, Charging & Troubleshooting & Recycling. 18 Specification. 19 Warranty. 19 CALIFORNIA PROP 65 WARNING * Some dust created by power sanding, sawing, grinding, drilling and other construction activities contains chemicals known to the state of California to cause cancer, birth defects or other reproductive harm.
PAGE 3
Cordless Circular Saw Overview A. Gator Housing F. Battery Pack L. Fence Lock Knob B. Trigger Switch Lock-off G. Upper Saw Guard M. Bevel Adjustment Knob Button H. Lower Guard Lever N. Depth Adjustment Lever & Trigger Switch 1. Arbor Bolt . Spindle Lock Button D. Soft Grip J. Lower Guard P. Artery Charger E. Battery Release Button K.shoe Please read before resuming this product for any reason: If you have question or experience a problem with your Hyper Tough purchase, call 1-800-840-7856 from 8:00 a.m.
PAGE 4
Cordless Circular Saw Workplace/Electrical Safety SAVE THESE WARNINGS AND INSTRUCTIONS 'YOU MAY NEED TO REFER TO THEM LATER The term “power too!” in the WARNING refers to your AC power(corded) power too or battery-operated (cordless) power tool. SAVE THESE INSTRUCTIONS WORK AREA SAFETY 1. Keep work area clean and well lit. Cluttered or dark areas invite accidents. 2. Do not operate power tools in explosive atmospheres, such sin the presence of flammable liquids, gases or dust.
PAGE 5
Cordless Circular Saw Personal safety/Power tool use and care PERSONAL SAFETY 1. Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the Influence of drugs, alcohol or medication, A moment of inattention while operating power tools may result in serious personal Injury. 2, Use personal protective equipment, Always wear eye protection.
PAGE 6
Cordless Circular Saw Battery/Service accidents are caused by poorly maintained power tools. 6. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. 7. Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed.
PAGE 7
Cordless Circular Saw Additional safety rules WARNING: Changes or modification to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAGE 8
Specific Safety Rules/Lower Guard 7. Watch what you are doing and use common sense. Don’t operate any tool when you are tired. SPECIFIC SAFETY RULES CUTTING PROCEDURES 1. DANGER: Keep hands away from cutting area and the blade. Keep your second hand on auxiliary handle, or motor housing. If both hands are holding the saw, they cannot be cut by the blade. 2. Do not reach underneath the work piece. The guard cannot protect you from the blade below the work piece. 3.
PAGE 9
Cordless Circular Saw Specific Safety Rules/Klckback 3. Lower guard may be retracted manually only for special cuts such as "plunge cuts™ and "compound cuts". Raise lower guard by retracting handle and as soon as blade enters the material, the lower guard must be released. For all other sawing, the lower guard should operate automatically. 4, Always observe that the lower guard is covering the blade before placing saw down on bench or floor.
PAGE 10
Cordless Circular Saw Symbols blade is binding, it may walk up or kickback from the work piece as the saw is restarted. 8. Support large panels to minimize the risk of blade pinching and kickback. Large panels tend to sag under their own weight. Supports must be placed under the panel on both sides, near the line of cut and near the edge of the panel. 9. Do not use dull or damaged blades. Sharpened or improperly set blades produce narrow serf causing excessive friction, blade binding and kickback. 10.
PAGE 11
Cordless Circular Saw Charging The Battery Pack BEFORE ATTEMPTING TO CHARGE YOUR BATTERY PACK, THOROUGHLY READ ALL THE SAFETY INSTRUCTIONS. CAUTION: *The battery s not fully charged. Before first use, the battery pack requires 5.7 hours charge time to be fully charged. Subsequent recharging needs 3 4 hours for the battery to be fully charged.
PAGE 12
Cordless Circular Saw Operation tool will automatically stop during operation if the tool or battery is placed under one of the following conditions: OVERLOAD PROTECTION When the battery is operated in a manner that causes it to draw an abnormally high current, the tool automatically stops without any indication. In this situation, turn the tool off and stop the application that caused the tool to become overloaded. Then turn the tool on to restart.
PAGE 13
Cordless Circular Saw Operation 3. Hold the saw with one hand on the main handle and the other hand on the auxiliary handle. 4. Align saw on cut line with the larger part of the work piece to the left of the saw blade. 5.Push in and hold trigger lock on either side, then press trigger. 6. Allow the blade to come up to full speed before contacting the work piece. 7. After completing the cut, release the trigger. Make sure that the lower guard closes immediately. 8.
PAGE 14
Cordless Circular Saw Operation /N WARNING: Tighten fence lock knob before use. KICKBACK Kickback occurs when the blade stalls rapidly and the saw is driven back towards you. Blade stalling is caused by any action which pinches the blade in the wood. /\ WARNING: When using the saw, always stay alert and exercise control. Do not remove the saw from the work piece while the blade is moving. BLADE INSTALLATION 1. Remove the battery pack from the tool 2. Use supplied hex wrench. 3.
PAGE 15
Cordless Circular Saw Operation BLADE GUARD SYSTEM The lower blade guard attached to the circular saw is there for your protection and safety. Do not alter it for any reason. If it becomes damaged, do not operate the saw until you have the guard repaired or replaced. Always leave guard in operating position when using the saw. DANGER: When sawing through work, lower blade guard does not cover blade on the underside of work.
PAGE 16
Cordless Circular Saw Operation an accurate cut. NOTE: The distance from the line of cut to the guideline is the amount you should offset the guide. BEVEL CUTTING 1. Align the line of cut with the 45° blade guide notch on the base when making 45°bevel cuts. 2. Make a trial cut in scrap material along a guideline to determine how much you should offset the guideline on the cutting material. 3. Adjust the angle of the cut to any desired setting between zero and 50°. {Refer to Adjusting the Bevel Setting next.
PAGE 17
PAGE 18
Cordless Circular Saw Recycling THE RBRC™ SEAL The RBRC™ SEAL (Rechargeable Battery Recycling corporation) on the lithium-ion battery {or battery pack) indicates that the cost of recycling the battery or battery pack have already been paid by Hyper Tough. In some areas it is illegal to place spent lithium-ion batteries in the trash or municipal solid waste stream and the CURB program provides an environmentally conscious alternative.
PAGE 19
Cordless Circular Saw Speclfications/Warranty SPECIFICATIONS Product model: AQ80001G Rated voltage: 20V Max DC Battery pack model: AQ90050G Charger model: EBSO090A-2000450AU Input: 0.3A Output: 20.0V 450mAh Machine Weight: 5.73 Ibs. (2.60 kg) No Load Speed: 4000 RPM Blade size: Max cutting depth: Bevel degrees: 45° INCLUDES: + 1pc HT Charge 20v Max Cordless Circular Saw + 1pc HT Charge 1500mAh lee-ion battery pack + 1pc HT Charge battery charger .
PAGE 20
